113 True RMS Utility Multimeter 3078875

The Fluke 113 True-RMS Utility Multimeter is a digital multimeter (also known as a multitester) that measures AC/DC voltage to 600V, resistance to 60 kiloohms, and capacitance to 9,999 microfarads. The meter has a diode check for testing general-purpose germanium, silicon, and power diodes, and a continuity beeper which provides audible detection of resistance by turning on at less than 25 ohms and off at 250 ohms. It is also able to simultaneously check for voltage and continuity. This true RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or non-sinusoidal waveform and has both manual- and auto-ranging capabilities for user flexibility. A Max/Min function records signal fluctuations and a hold function freezes measurements on the display. The 6000-count resolution, 3-1/2 digit digital display is backlit for readability in low-light conditions. The meter is safety rated for Category III to 600V and Category IV to 300V. It uses a 9V battery (installed) with a battery life of approximately 300 hours without backlight and has a sleep mode to maximize battery life. The meter measures 6.58 x 3.35 x 1.81 inches (H x W x D) and weighs 13 oz. /404 g. (H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.) This meter includes a holster with built-in probe holders for convenient storage. Multimeters are electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. Available in handheld or benchtop models, multimeters diagnose electrical problems in electrical equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Multimeters display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electro technical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications.

Manufacture: Fluke
Product Description: UTILITY MULTIMETER
The Fluke 113 Digital Multimeter gives users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 has significant improvements over other digital multimeters available on the market, including Fluke model 7-600. Using the Fluke VCHEK LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Min/Max function lets you record signal fluctuations. The Fluke 113 can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display thats easier to view, this meter is a must have for every toolbox.
True-rms ac voltage and current for accurate measurements on non-linear signalsMeasure up to 1000 V ac and dcMeasure up to 10 A (20 A for 30 seconds)10,000 microF capacitance rangeFrequency to 50 kHzBuilt in thermometer conveniently allows you to take temperature readings without having to carry a separate instrumentResistance, continuity and diode testLow power wireless technology allows the display to be carried up to 10 meters (33 ft) away from the point of measurement for added flexibility.No interference with measurementsThe removable magnetic display can be conveniently mounted where it is easily seenMake measurements without holding the meter to improve visual focus on probes and augment safe electrical measurementsUse as a conventional multimeter when the display is connectedRadio transmitter automatically turns off when the display is connected to the meterAuto power off maximizes battery lifeMin/Max and Average recording to capture variations automaticallyTest continuity and diodesEasy to read display with large digits and bright backlightBattery life approximately 400 hours

Key Features

Digital multimeter measures AC/DC voltage, resistance, and capacitance and performs continuity and diode tests
True RMS meter provides accurate readings when measuring linear or nonlinear loads where the current or voltage has a sinusoidal or non-sinusoidal waveform
Simultaneously checks for voltage and continuity
Manual and auto ranging modes for user flexibility
Safety rated for Category III to 600Volts and Category IV to 300 Volts